I run Nokian WR G4s, and they're noticeably better than the stock Bridgestone Turanza all-seasons my car came with from the factory, but they're loud and not a huge improvement in icy conditions. They're... okay. Not as durable as a regular all-season either, but assuredly better for summer wear than a true winter tire.
I run Nokian WR G4s, and they're noticeably better than the stock Bridgestone Turanza all-seasons my car came with from the factory, but they're loud and not a huge improvement in icy conditions. They're... okay. Not as durable as a regular all-season either, but assuredly better for summer wear than a true winter tire.
And they get louder and louder as the tread wears as that's the major tradeoff with these tires.
Yeah I used to run the Nokian WR whatevers on my VW Passat and Nissan Murano and yeah they were ok. Good enough that if I was in a situation where I could only have 1 set of tires it'd be ok, but if you can manage to swap then I'd say swap.
__________________ Uncertainty is an uncomfortable position.
But certainty is an absurd one.
Apparently you can drive fairly decently missing a wheel. Probably not recommended though.
Yup. My parents were moving, and Dad ended up losing one of the rear tires off his F150. He was able to pull over pretty much immediately, though a ton of damage had already been done to the brake assembly by that time.
My dad got a torque wrench says he wants to replace his winters himself this year, so I figure we can do it together.
He was just going to jack it up one corner at a time but I'm not sure I'd trust the little jack that comes with my car (or the hydraulics of a floor jack).
It seems to me like a floor jack with a couple of jack stands would be safer, but is there a way to do one corner at a time with a setup like that? Can't put the jack stand on the point where it's being jacked up obviously, would there be somewhere else to put a jack stand just for safety while doing that corner?
Also my car has some hub rings, but just thinking ahead how does one usually stop the rings from falling out of the wheel while putting the wheel on? Or are they usually tight enough that's not a problem? I suppose I could put them on the hub but they're plastic so seems like it'd be easy to damage them.
I assume just normal Princess Auto / Canadian Tire tier floor jack / jack stands are fine?
Yeah the place that I bought my rims from gives me free rim swaps, though getting the rims there last year I got my dad to bring them there with his truck, I'm not sure I could fit all 4 in my car lol.
Just figured if my dad wants to do his might as well do it together.
I don't think my car even has a middle front or back jack point so not sure how I'd use jack stands at all.
__________________ Uncertainty is an uncomfortable position.
But certainty is an absurd one.
I personally don't use jack stands when I change my wheels over. I'll take the very low odds of a jack failure in exchange for efficiency, provided that nobody is going under the car.
If you or part of you is going under the vehicle, jack stands are absolutely necessary - no compromise.
The Following 8 Users Say Thank You to Jimmy Stang For This Useful Post:
My dad got a torque wrench says he wants to replace his winters himself this year, so I figure we can do it together.
He was just going to jack it up one corner at a time but I'm not sure I'd trust the little jack that comes with my car (or the hydraulics of a floor jack).
It seems to me like a floor jack with a couple of jack stands would be safer, but is there a way to do one corner at a time with a setup like that? Can't put the jack stand on the point where it's being jacked up obviously, would there be somewhere else to put a jack stand just for safety while doing that corner?
Also my car has some hub rings, but just thinking ahead how does one usually stop the rings from falling out of the wheel while putting the wheel on? Or are they usually tight enough that's not a problem? I suppose I could put them on the hub but they're plastic so seems like it'd be easy to damage them.
I assume just normal Princess Auto / Canadian Tire tier floor jack / jack stands are fine?
Why not just use a jack pad/puck and lift the vehicle using the recommended frame section? You can easily jack up the vehicle and slide a stand under the vehicle once you get it up in the air.
The Following User Says Thank You to calgarygeologist For This Useful Post:
I personally don't use jack stands when I change my wheels over. I'll take the very low odds of a jack failure in exchange for efficiency, provided that nobody is going under the car.
If you or part of you is going under the vehicle, jack stands are absolutely necessary - no compromise.
Ya, I never use jack stands for tire changes. But I do use a good floor jack.
The Following 2 Users Say Thank You to Fuzz For This Useful Post:
Why not just use a jack pad/puck and lift the vehicle using the recommended frame section? You can easily jack up the vehicle and slide a stand under the vehicle once you get it up in the air.
The manual only shows these points for lift points:
I don't see anywhere else it says is ok to put a stand under the frame.
__________________ Uncertainty is an uncomfortable position.
But certainty is an absurd one.
What’s wrong with the jack that comes with the vehicle? I have been using it for a few years now to swap tires on our SUV. I am not getting underneath the car or anything and only lifting it as high as necessary to get the tires in/out.
I did buy a bottle jack though, cause the problem I have with the vehicle issued ones are: the screw gear is greasy and gross; and my hands get tired turning that awkward crank.
The Following User Says Thank You to Wormius For This Useful Post:
If the one that comes with the car is good enough to do a wheel swap then that seems easiest.
I think you'll find that manually cranking those small jacks for each tire gets old very quickly. A decent floor jack from Canadian Tire will be much faster, and if you can find a solid piece of frame on the front or back to put it under then you can do two tires at once
The Following 2 Users Say Thank You to Hemi-Cuda For This Useful Post:
Consider this the annual reminder to check the tread direction arrows before you snug up the lug nuts, drop the jack and move on to the next tire. Yeah.
The Following 6 Users Say Thank You to InglewoodFan For This Useful Post: